HIP4082 DATASHEET PDF

HIP datasheet, HIP pdf, HIP data sheet, datasheet, data sheet, pdf , Intersil, Driver, Full Bridge FET, No Charge Pump. HIP 80V/A Peak Current Full Bridge Fet Driver. The is a medium frequency, medium voltage H-Bridge N-Channel MOSFET driver IC, available in HIP Data Sheet. FN CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Author: Meztisar Shakticage
Country: Algeria
Language: English (Spanish)
Genre: Medical
Published (Last): 3 May 2013
Pages: 54
PDF File Size: 17.52 Mb
ePub File Size: 18.29 Mb
ISBN: 357-4-66761-160-4
Downloads: 30917
Price: Free* [*Free Regsitration Required]
Uploader: Kazilrajas

The HIP is a medium frequency, medium voltage. Drives pF Load in Free Air at 50? C with Rise and Fall. Times of Typically 15ns. User-Programmable Dead Time 0. Bootstrap Capacitor when Pulled Low. Similar to the HIP, it has a flexible input protocol for. HIP’s reduced drive current allows smaller packaging.

The HIP does not contain an internal charge. This set of features and specifications is optimized for. Full Bridge Power Supplies. Intersil Pb-free products employ special Pb-free material. Intersil Pb-free products are MSL. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Copyright Harris Corporation Copyright Intersil Americas Inc. All other trademarks mentioned are the property of their respective owners.

Supply Voltage, V DD. Lead Temperature Soldering 10s. All voltages are relative V SS unless otherwise specified. Voltage on V SS. Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device.

This is a stress only rating and operation of the. V DD Quiescent Current.

V DD Operating Current. Low Level Input Voltage. High Level Input Voltage. Low Level Input Current. High Level Input Current. Low Level Output Voltage. High Level Output Voltage.

  KESKIN KT8 GUTACHTEN PDF

80 V/1.25 A Peak Current Full Bridge FET Driver

Lower Turn-off Propagation Delay. Upper Turn-off Propagation Delay. Lower Turn-on Propagation Delay. Upper Turn-on Propagation Delay.

Minimum Input Pulse Width.

Output Pulse Response to 50 ns Input Pulse. Disable Turn-off Propagation Delay. DIS – Lower Outputs.

DIS – Upper Outputs. Disable Turn-on Propagation Delay. X signifies that input can ddatasheet either a “1” or “0”. B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap. Logic level input that controls BHO driver Pin Logic level input that controls BLO driver Pin If BHI Pin 2 is driven high or not connected.

The pin can be driven by signal levels of 0V to 15V no greater than. Logic level input that controls ALO driver Pin If AHI Pin 7 is driven high or not connected. Connect resistor from this pin to V SS to set timing current that defines the dead time between drivers. All drivers turn-off with no adjustable delay, so the DEL resistor guarantees no shoot-through by delaying the dqtasheet.

Chip negative supply, generally will be ground. Logic level input that controls Ddatasheet driver Pin Logic level input that when taken high sets all four outputs low.

DIS high overrides all other inputs. When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to.

A High-side Bootstrap supply. A High-side Source connection. Connect negative side of.

Positive supply to control logic and lower gate drivers. De-couple this pin to V SS Pin 6. B High-side Source connection. In case of conflict between English and.

  CASA DOS BUDAS DITOSOS PDF

Metric dimensions, the inch dimensions control. DEC seating plane gauge GS – 3. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0. E and e A are measured with the leads constrained to be perpendic.

B1 maximum dimensions do not include dambar protrusions. N is the maximum number of terminal positions. Dimension “D” does not hi;4082 mold flash, protrusions or gate.

Mold flash, protrusion and gate hip40082 shall not exceed. Dimension “E” does not include interlead flash or protrusions. The chamfer on the body is optional.

If it is not present, a visual. Terminal numbers are shown for reference only. The lead width “B”, as measured 0. Intersil Corporation’s quality certifications can be viewed at www. Intersil products are sold by description only. Accordingly, the reader is cautioned to verify that data sheets are current before placing dstasheet.

HIP Datasheet pdf – Driver, Full Bridge FET, No Charge Pump – Intersil

Information furnished by Intersil is believed to be accurate and. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.